View ADT7484A_4888083.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ADT7484A/ADT7486A Digital Temperature Sensor with SST Interface
The ADT7484A/ADT7486A are simple digital temperature sensors for use in PC applications with a Simple Serial Transport (SST) interface. These devices can monitor their own temperature as well as the temperature of one (ADT7484A) or two (ADT7486A) remote sensor diodes. The ADT7484A/ADT7486A are controlled by a single SST bidirectional data line. The devices are fixed-address SST clients where the target address is chosen by the state of the two address pins, ADD0 and ADD1.
Features http://onsemi.com MARKING DIAGRAMS
8 SOIC-8 CASE 751 1 A L Y W G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package 8 MSOP-8 CASE 846AB 1 10 MSOP-10 CASE 846AC 1 T22 AYWG G T20 AYWG G T7484A ALYWG G
* * * *
1
1 On-Chip Temperature Sensor 1 or 2 Remote Temperature Sensors Simple Serial Transportt (SSTt) Interface Rev 1 Compliant These are Pb-Free Devices
Applications
* Personal Computers * Portable Personal Devices * Industrial Sensor Nets
1
1 T2x A Y W G
= Specific Device Code = Assembly Location = Year = Work Week = Pb-Free Package
(Note: Microdot may be in either location)
PIN ASSIGNMENTS
VCC 1 GND 2 D1+ 3 D1- 4
8
SST ADD0 RESERVED ADD1
ADT7484A
7 6 5
(Top View)
VCC 1 GND 2 D1+ 3 D1- 4 D2+ 5
10 9
SST ADD0 RESERVED ADD1 D2-
ADT7486A
8 7 6
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 11 of this data sheet.
(c) Semiconductor Components Industries, LLC, 2009
December, 2009 - Rev. 4
1
Publication Order Number: ADT7484A-86A/D
ADT7484A/ADT7486A
ON-CHIP TEMPERATURE SENSOR LOCAL TEMPERATURE VALUE REGISTER DIGITAL MUX SST INTERFACE SST
D1+ D1- (ADT7486A ONLY) D2+ D2- ANALOG MUX
A/D CONVERTER
REMOTE TEMPERATURE VALUE REGISTER
ADT7484A/ ADT7486A
VDD GND
OFFSET REGISTERS
ADDRESS SELECTION
ADD1 ADD0
RESERVED
Figure 1. Functional Block Diagram
ABSOLUTE MAXIMUM RATINGS
Parameter Supply Voltage (VCC) Voltage on Any Other Pin (Including SST Pin) Input Current at Any Pin Package Input Current Maximum Junction Temperature (TJ max) Storage Temperature Range Lead Temperature, Soldering IR Reflow Peak Temperature Lead Temperature, Soldering (10 sec) Rating 3.6 3.6 5.0 20 150 -65 to +150 260 300 Unit V V mA mA C C C
ESD Rating 1500 V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. NOTE: This device is ESD sensitive. Use standard ESD precautions when handling.
THERMAL CHARACTERISTICS
Package Type 8-Lead MSOP and 8-Lead SOIC NB Packages (ADT7484A) 10-Lead MSOP (ADT7486A) NOTE: qJA 206 qJC 44 Unit C/W
qJA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages.
http://onsemi.com
2
ADT7484A/ADT7486A
ADT7484A PIN ASSIGNMENT
Pin No. 1 2 3 4 5 6 7 8 Mnemonic VCC GND D1+ D1- ADD1 RESERVED ADD0 SST Ground Analog input Analog input Digital input Reserved Digital input Digital input/output Type Power supply 3.3 V 10%. Ground Pin. Positive Connection to Remote Temperature Sensor. Negative Connection to Remote Temperature Sensor. SST Address Select. Connect to Ground. SST Address Select. SST Bidirectional Data Line. Description
ADT7486A PIN ASSIGNMENT
Pin No. 1 2 3 4 5 6 7 8 9 10 Mnemonic VCC GND D1+ D1- D2+ D2- ADD1 RESERVED ADD0 SST Ground Analog input Analog input Analog input Analog input Analog input Analog input Digital input Digital input/output Type Power supply 3.3 V 10%. Ground Pin. Positive Connection to Remote 1 Temperature Sensor. Negative Connection to Remote 1 Temperature Sensor. Positive Connection to Remote 2 Temperature Sensor. Negative Connection to Remote 2 Temperature Sensor. SST Address Select. Connect to Ground. SST Address Select. SST Bidirectional Data Line. Description
ELECTRICAL CHARACTERISTICS (TA = TMIN to TMAX, = VCC = VMIN to VMAX, unless otherwise noted)
Parameter Power Supply Supply Voltage, VCC Undervoltage Lockout Threshold Average Operating Supply Current, IDD Temperature-to-Digital Converter Local Sensor Accuracy Remote Sensor Accuracy 40C TA 70C, VCC = 3.3 V 5% -40C TA +100C -40C TD +125C; TA = 25C; VCC = 3.3 V -40C TD +125C; -40 TA 70C, VCC = 3.3 V 5% -40C TD +125C; -40 TA +100C Remote Sensor Source Current Low level Mid level High level The ADT7484A and ADT7486A cancel 1.5 kW in series with the remote thermal diode 12 80 204 0.016 1.5 +1.0 +1.0 1.75 4.0 1.0 1.75 C C C C Continuous conversions 3.0 3.3 2.8 3.8 5.0 3.6 V V mA Conditions Min Typ Max Unit
4.0
C mA
Resolution Series Resistance Cancellation
C kW
1. Guaranteed by design, not production tested. 2. Minimum and maximum bit times are relative to tBIT defined in the timing negotiation pulse. 3. Devices compatible with hold time specification as driven by SST originator.
http://onsemi.com
3
ADT7484A/ADT7486A
ELECTRICAL CHARACTERISTICS (TA = TMIN to TMAX, = VCC = VMIN to VMAX, unless otherwise noted)
Parameter Temperature-to-Digital Converter Conversion Time (Local Temperature) (Note 1) Conversion Time (Remote Temperature) (Note 1) Total Monitoring Cycle Time (Note 1) Digital Inputs (ADD0, ADD1) Input High Voltage, VIH Input Low Voltage, VIL Input High Current, IIH Input Low Current, IIL Pin Capacitance Digital I/O (SST Pin) Input High Voltage, VIH Input Low Voltage, VIL Hysteresis (Note 1) Output High Voltage, VOH High Impedance State Leakage, ILEAK High Impedance State Leakage, ILEAK Signal Noise Immunity, VNOISE SST Timing Bitwise Period, tBIT High Level Time for Logic 1, tH1 (Note 2) High Level Time for Logic 0, tH0 (Note 2) Time to Assert SST High for Logic 1, tSU, HIGH Hold Time, tHOLD (Note 3) Stop Time, tSTOP Time to Respond After a Reset, tRESET Response Time to Speed Negotiation After Powerup Time after powerup when device can participate in speed negotiation 500 See SST Specification Rev 1.0 Device responding to a constant low level driven by originator 1.25 x tBIT 2 x tBIT tBIT defined in speed negotiation 0.495 0.6 x tBIT 0.2 x tBIT 0.75 x tBIT 0.25 x tBIT 500 0.8 x tBIT 0.4 x tBIT 0.2 x tBIT 0.5 x tBIT-M 2 x tBIT 0.4 ms ms ms ms ms ms ms ms Between input switching levels ISOURCE = 6 mA (maximum) Device powered on SST bus; VSST = 1.1 V, VCC = 3.3 V Device unpowered on SST bus; VSST = 1.1 V, VCC = 0 V Noise glitches from 10 MHz to 100 MHz; width up to 50 ns 300 1.1 150 1.9 1.0 10 1.1 0.4 V V mV V mA mA mV p-p VIN = VCC VIN = 0 5.0 -1.0 1.0 2.3 0.8 V V mA mA pF Averaging enabled Averaging enabled Averaging enabled 12 12 38 50 ms ms ms Conditions Min Typ Max Unit
1. Guaranteed by design, not production tested. 2. Minimum and maximum bit times are relative to tBIT defined in the timing negotiation pulse. 3. Devices compatible with hold time specification as driven by SST originator.
http://onsemi.com
4
ADT7484A/ADT7486A
TYPICAL CHARACTERISTICS
1.55 1.50 750 (~2mA) 1.45 SST O/P (V) IDD (mA) 1.40 270 (~5.2mA) 1.35 1.30 1.25 1.20 2.6 3.56 3.55 3.54 3.53 3.52 3.51 3.50 3.49 120 (~10.6mA) 3.48 3.47 3.46 2.8 3.0 3.2 VCC (V) 3.4 3.6 3.45 -45 -25 -5 15 35 55 75 95 115 DEV1 DEV2 DEV3
TEMPERATURE (5C)
Figure 2. SST O/P Level vs. Supply Voltage
Figure 3. Supply Current vs. Temperature
7 6 TEMPERATURE ERROR (5C) 5 4 3 2 1 0 -1 -60 LO SPEC (VCC = 3.6V) -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (5C) HI SPEC (VCC = 3V) MEAN (VCC = 3.3V)
1.55 1.50 1.45 SST O/P (V) 1.40 1.35 1.30 1.25 1.20 -50 120 (~10.6mA) 270 (~5.2mA) 750 (~2mA)
0
50 TEMPERATURE (5C)
100
150
Figure 4. Local Temperature Error
Figure 5. SST O/P Level vs. Temperature
3.9
7 6 TEMPERATURE ERROR (5C)
3.7 DEV2 3.5 DEV3 DEV1 3.3
5 4 3 2 1 MEAN (VCC = 3.3V) HI SPEC (VCC = 3V)
IDD (mA)
3.1
2.9 2.65
LO SPEC (VCC = 3.6V) 2.85 3.05 VCC (V) 3.25 3.45 3.65 -2 -60 -40 -20 0 20 40 60 80 100 120 140
TEMPERATURE (5C)
Figure 6. Supply Current vs. Voltage
Figure 7. Remote Temperature Error
http://onsemi.com
5
ADT7484A/ADT7486A
TYPICAL CHARACTERISTICS
15 10 5 D+ TO GND DEV1_EXT1 DEV1_EXT2 DEV2_EXT1 DEV2_EXT2 DEV3_EXT1 DEV3_EXT2 TEMPERATURE ERROR (5C) 30 25 20 15 60mV 10 5 0 -5 10k 100mV
ERROR (C)
10 15 20 25 -30 -35 -40 0 20 D+ TO VCC
DEV1_EXT1 DEV1_EXT2 DEV2_EXT1
DEV2_EXT2 DEV3_EXT1 DEV3_EXT2
40mV
40
60
80
100
100k
1M
10M
100M
1G
RESISTANCE (M)
NOISE FREQUENCY (5C)
Figure 8. Remote Temperature Error vs. PCB Resistance
20
Figure 9. Temperature Error vs. Common-Mode Noise Frequency
0 -10
15 TEMPERATURE ERROR (5C) -20 10 ERROR (5C) -30 40 50 -60 50mV 70 -5 80 -10 10k 100k 1M 10M 100M 1G -90 0 10 20 30 40 50 EXT1 EXT2
5 125mV 0
POWER SUPPLY NOISE FREQUENCY (Hz)
CAPACITANCE (nF)
Figure 10. Local Temperature Error vs. Power Supply Noise
7 6 TEMPERATURE ERROR (5C) 5 4 3 2 1 10mV 0 10k 100k 1M 10M 100M 1G 20mV 40mV TEMPERATURE ERROR (5C)
Figure 11. Remote Temperature Error vs. Capacitance Between D1+ and D1-
5 4 3 2 1 0 50mV -1 -2 -3 10k
125mV
100k
1M
10M
100M
1G
NOISE FREQUENCY (5C)
POWER SUPPLY NOISE FREQUENCY (Hz)
Figure 12. Temperature Error vs. Differential-Mode Noise Frequency
Figure 13. Remote Temperature Error vs. Power Supply Noise
http://onsemi.com
6
ADT7484A/ADT7486A
Product Description
The ADT7484A is a single remote temperature sensor, and the ADT7486A is a dual temperature sensor for use in PC applications. The ADT7484A/ADT7486A accurately measure local and remote temperature and communicate over a one-wire Simple Serial Transport (SST) bus interface.
SST Interface
ADT7486A to distinguish between three input states: high, low (GND), and floating. The address range for fixed address, discoverable devices is 0x48 to 0x50.
Table 1. ADT7484A/ADT7486A Selectable Addresses
ADD1 Low (GND) Low (GND) Low (GND) Float Float Float High High High ADD0 Low (GND) Float High Low (GND) Float High Low (GND) Float High Address Selected 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F 0x50
Simple Serial Transport (SST) is a one-wire serial bus and a communications protocol between components intended for use in personal computers, personal handheld devices, or other industrial sensor nets. The ADT7484A/ADT7486A support SST specification Rev 1. SST is a licensable bus technology from Analog Devices, Inc., and Intel Corporation. To inquire about obtaining a copy of the Simple Serial Transport Specification or an SST technology license, please email Analog Devices, at sst_licensing@analog.com or write to Analog Devices, 3550 North First Street, San Jose, CA 95134, Attention: SST Licensing, M/S B7-24.
ADT7484A/ADT7486A Client Address
Command Summary
The client address for the ADT7484A/ADT7486A is selected using the address pin. The address pin is connected to a float detection circuit, which allows the ADT7484A/
Table 2. Command Code Summary
Command Ping() GetIntTemp() GetExt1Temp() GetExt2Temp() GetAllTemps() Command Code, CC 0x00 0x00 0x01 0x02 0x00 Write Length, WL 0x00 0x01 0x01 0x01 0x01
Table 7 summarizes the commands supported by the ADT7484A/ADT7486A devices when directed at the target address selected by the fixed address pins. It contains the command name, command code (CC), write data length (WL), read data length (RL), and a brief description.
Read Length, RL 0x00 0x02 0x02 0x02 0x04 (ADT7484A) 0x06 (ADT7486A) 0x00 0x02 0x00 0x02 0x00
Description Shows a nonzero FCS over the header if present. Shows the temperature of the device's internal thermal diode. Shows the temperature of External Thermal Diode 1. Shows the temperature of External Thermal Diode 2 (ADT7486A only). Shows a 4- or 6-byte block of data (ADT7484A: GetIntTemp, GetExt1Temp; ADT7486A: GetIntTemp, GetExt1Temp, GetExt2Temp). Sets the offset used to correct errors in External Diode 1. Shows the offset that the device is using to correct errors in External Diode 1. Sets the offset used to correct errors in External Diode 2 (ADT7486A only). Shows the offset that the device is using to correct errors in External Diode 2 (ADT7486A only). Functional reset. The ADT7484A/ADT7486A also respond to this command when directed to the Target Address 0x00. Shows information used by SW to identify the device's capabilities. Can be in 8- or 16-byte format.
SetExt1Offset() GetExt1Offset() SetExt2Offset() GetExt2Offset() ResetDevice()
0xe0 0xe0 0xe1 0xe1 0xf6
0x03 0x01 0x03 0x01 0x01
GetDIB()
0xf7 0xf7
0x01 0x01
0x08 0x10
http://onsemi.com
7
ADT7484A/ADT7486A
Command Code Details
ADT7484A/ADT7486A Device Identifier Block Table 5. Reset Device() Command
Target Address Device Address Write Length 0x01 Read Length 0x00 Reset Command 0xf6 FCS
The GetDIB() command retrieves the device identifier block (DIB), which provides information to identify the capabilities of the ADP7484A/ADT7486A. The data returned can be in 8- or 16-byte format. The full 16-bytes of DIB is detailed in Table 3. The 8-byte format involves the first eight bytes described in this table. Byte-sized data is returned in the respective fields as it appears in Table 3. Word-sized data, including vendor ID, device ID, and data values use little endian format, that is, the LSB is returned first, followed by the MSB.
Table 3. DIB Byte Details
Byte Name Device Capabilities Version/ Revision Vendor ID Value 0xc0 0x10 00x11d4 Description Fixed address device Meets Version 1 of the SST specification Contains company ID number in little endian format Contains device ID number in little endian format SST device Reserved Reserved Reserved Reserved Reserved Reserved Reserved Contains revision ID Dependent on the state of the address pins
GetIntTemp()
The ADT7484A/ADT7486A show the local temperature of the device in response to the GetIntTemp() command. The data has a little endian, 16-bit, twos complement format.
GetExtTemp()
0 1
2, 3
Prompted by the GetExtTemp() command, the ADT7484A/ADT7486A show the temperature of the remote diode in little endian, 16-bit, twos complement format. The ADT7484A/ADT7486A show 0x8000 in response to this command if the external diode is an open or short circuit.
GetAllTemps()
4, 5
Device ID
0x7484 or 0x7486 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x05 0x48 to 0x50
6 7 8 9 10 11 12 13 14
Device Interface Function Interface Reserved Reserved Reserved Reserved Reserved Reserved Revision ID Client Device Address
The ADT7484A shows the local and remote temperatures in a 4-byte block of data (internal temperature first, followed by External Temperature 1) in response to a GetAllTemps() command. The ADT7486A shows the local and remote temperatures in a 6-byte block of data (internal temperature first, followed by External Temperature 1 and External Temperature 2) in response to this command.
SetExtOffset()
This command sets the offset that the ADT7484A/ ADT7486A will use to correct errors in the external diode. The offset is set in little endian, 16-bit, twos complement format. The maximum offset is 128C with +0.25C resolution.
GetExtOffset()
15
This command causes the ADT7484A/ADT7486A to show the offset that they are using to correct errors in the external diode. The offset value is returned in little endian format, that is, LSB before MSB.
ADT7484A/ADT7486A Response to Unsupported Commands
Ping()
The Ping() command verifies if a device is responding at a particular address. The ADT7484A/ADT7486A show a valid nonzero FCS in response to the Ping() command when correctly addressed.
Table 4. Ping() Command
Target Address Device Address Write Length 0x00 Read Length 0x00 FCS
ResetDevice()
This command resets the register map and conversion controller. The reset command can be global or directed at the client address of the ADT7484A/ADT7486A.
A full list of command codes supported by the ADT7484A/ADT7486A is given in Table 7. The offset registers (Command Codes 0xe0 and 0xe1) are the only registers that the user can write to. The other defined registers are read only. Writing to Register Addresses 0x03 to 0xdf shows a valid FSC, but no action is taken by the ADT7484A/ADT7486A. The ADT7484A/ADT7486A show an invalid FSC if the user attempts to write to the devices between Command Codes 0xe2 to 0xee and no data is written to the device. These registers are reserved for the manufacturer's use only, and no data can be written to the device via these addresses.
http://onsemi.com
8
ADT7484A/ADT7486A
Temperature Measurement
The ADT7484A/ADT7486A each have two dedicated temperature measurement channels: one for measuring the temperature of an on-chip band gap temperature sensor, and one for measuring the temperature of a remote diode, usually located in the CPU or GPU. The ADT7484A monitors one local and one remote temperature channel, whereas the ADT7486A monitors one local and two remote temperature channels. Monitoring of each of the channels is done in a round-robin sequence. The monitoring sequence is in the order shown in Table 11.
Table 6. Temperature Monitoring Sequence
Channel Number 0 1 2 Measurement Local Temperature Remote Temperature 1 Remote Temperature 2 (ADT7486A only) Conversion Time (ms) 12 38 38
calculated using the two DVBE measurements. This method can also cancel the effect of series resistance on the temperature measurement. The resulting DVBE waveforms are passed through a 65 kHz low-pass filter to remove noise and then through a chopper-stabilized amplifier to amplify and rectify the waveform, producing a dc voltage proportional to DVBE. The ADC digitizes this voltage, and a temperature measurement is produced. To reduce the effects of noise, digital filtering is performed by averaging the results of 16 measurement cycles for low conversion rates. Signal conditioning and measurement of the internal temperature sensor is performed in the same manner.
VDD I N1 x I N2 x I IBIAS
D+ REMOTE SENSING TRANSISTOR C1* D- BIAS DIODE LOW-PASS FILTER fC = 65kHz
VOUT+ TO ADC VOUT-
Temperature Measurement Method
*CAPACITOR C1 IS OPTIONAL. IT SHOULD ONLY BE USED IN NOISY ENVIRONMENTS.
A simple method for measuring temperature is to exploit the negative temperature coefficient of a diode by measuring the base-emitter voltage (VBE) of a transistor operated at constant current. Unfortunately, this technique requires calibration to null the effect of the absolute value of VBE, which varies from device to device. The technique used in the ADT7484A/ADT7486A measures the change in VBE when the device is operated at three different currents. Figure 16 shows the input signal conditioning used to measure the output of a remote temperature sensor. This figure shows the remote sensor as a substrate transistor, which is provided for temperature monitoring on some microprocessors, but it could also be a discrete transistor. If a discrete transistor is used, the collector is not grounded and should be linked to the base. To prevent ground noise from interfering with the measurement, the more negative terminal of the sensor is not referenced to ground, but is biased above ground by an internal diode at the D1- input. If the sensor is operating in an extremely noisy environment, C1 can be added as a noise filter. Its value should not exceed 1000 pF. To measure DVBE, the operating current through the sensor is switched between three related currents. Figure 16 shows N1 x I and N2 x I as different multiples of the current I. The currents through the temperature diode are switched between I and N1 x I, giving DVBE1, and then between I and N2 x I, giving DVBE2. The temperature can then be
Figure 14. Signal Conditioning for Remote Diode Temperature Sensors Reading Temperature Measurements
The temperature measurement command codes are detailed in Table 12. The temperature data returned is two bytes in little endian format, that is, LSB before MSB. All temperatures can be read together by using Command Code 0x00 with a read length of 0x04. The command codes and returned data are described in Table 12.
Table 7. Temperature Channel Command Codes
Temp Channel Internal External 1 External 2 All Temps Command Code 0x00 0x01 0x02 0x00 Returned Data LSB, MSB LSB, MSB LSB, MSB Internal LSB, Internal MSB; External 1 LSB, External 1 MSB; External 2 LSB, External 2 MSB
http://onsemi.com
9
ADT7484A/ADT7486A
SST Temperature Sensor Data Format
The data for temperature is structured to allow values in the range of 512C to be reported. Thus, the temperature sensor format uses a twos complement, 16-bit binary value to represent values in this range. This format allows temperatures to be represented with approximately a 0.016C resolution.
Table 8. SST Temperature Data Format
Temperature (5C) -125 -80 -40 -20 -5 -1 0 +1 +5 +20 +40 +80 +125 Twos Complement MSB 1110 0000 1110 1100 1111 0110 1111 1011 1111 1110 1111 1111 0000 0000 0000 0000 0000 0001 0000 0100 0000 1010 0001 0100 0001 1111 LSB 1100 0000 0000 0000 0000 0000 0011 1110 1100 0000 1100 0000 0000 0000 0100 0000 0100 0000 1100 0010 0000 0000 0000 0000 0100 0000
* *
such as clock generators, data/address buses, and CRTs, are avoided, this distance can be four to eight inches. Route the D1+ and D1- tracks close together in parallel with grounded guard tracks on each side. Provide a ground plane under the tracks if possible. Use wide tracks to minimize inductance and reduce noise pickup. A 5 mil track minimum width and spacing is recommended.
GND 5MIL 5MIL D+ 5MIL 5MIL D- 5MIL 5MIL GND 5MIL
Figure 16. Arrangements of Signal Tracks
* Try to minimize the number of copper/solder joints,
Using Discrete Transistors
If a discrete transistor is used, the collector is not grounded and should be linked to the base. If a PNP transistor is used, the base is connected to the D1- input and the emitter is connected to the D1+ input. If an NPN transistor is used, the emitter is connected to the D1- input and the base is connected to the D1+ input. Figure 17 shows how to connect the ADT7484A/ADT7486A to an NPN or PNP transistor for temperature measurement. To prevent ground noise from interfering with the measurement, the more negative terminal of the sensor is not referenced to ground, but is biased above ground by an internal diode at the D1- input.
2N3904 NPN
D+ D-
ADT7484A/ ADT7486A
2N3906 PNP
D+ D-
ADT7484A/ ADT7486A
Figure 15. Connections for NPN and PNP Transistors
The ADT7484A/ADT7486A show an external temperature value of 0x8000 if the external diode is an open or short circuit.
Layout Considerations
Digital boards can be electrically noisy environments. Take the following precautions to protect the analog inputs from noise, particularly when measuring the very small voltages from a remote diode sensor: * Place the device as close as possible to the remote sensing diode. Provided that the worst noise sources,
which can cause thermocouple effects. Where copper/solder joints are used, make sure that they are in both the D1+ and D1- paths and are at the same temperature. * Thermocouple effects should not be a major problem because 1C corresponds to about 240 mV, and thermocouple voltages are about 3 mV/C of the temperature difference. Unless there are two thermocouples with a big temperature differential between them, thermocouple voltages should be much less than 200 mV. * Place a 0.1 mF bypass capacitor close to the device. * If the distance to the remote sensor is more than eight inches, the use of a twisted-pair cable is recommended. This works for distances of about 6 to 12 feet. * For very long distances (up to 100 feet), use shielded twisted-pair cables, such as Belden #8451 microphone cables. Connect the twisted-pair cable to D1+ and D1- and the shield to GND, close to the device. Leave the remote end of the shield unconnected to avoid ground loops. Because the measurement technique uses switched current sources, excessive cable and/or filter capacitance can affect the measurement. When using long cables, the filter capacitor can be reduced or removed. Cable resistance can also introduce errors. A 1 W series resistance introduces about 0.5C error.
http://onsemi.com
10
ADT7484A/ADT7486A
Temperature Offset Application Schematics
VCC
1 2
As CPUs run faster, it is more difficult to avoid high frequency clocks when running the D1+ and D1- tracks around a system board. Even when the recommended layout guidelines are followed, there may still be temperature errors, attributed to noise being coupled on to the D1+ and D1- lines. High frequency noise generally has the effect of producing temperature measurements that are consistently too high by a specific amount. The ADT7484A/ ADT87486A have a temperature offset command code of 0xe0 through which a desired offset can be set. By doing a one-time calibration of the system, the offset caused by system board noise can be calculated and nulled by specifying it in the ADT7484A/ADT7486A. The offset is automatically added to every temperature measurement. The maximum offset is 128C with 0.25C resolution. The offset format is the same as the temperature data format; 16-bit, twos complement notation, as shown in Table 8. The offset should be programmed in little endian format, that is, LSB before MSB. The offset value is also returned in little endian format when read.
ADT7484A
VCC GND SST ADD0
8 7 6 5
SST
2N3904 OR CPU THERMAL DIODE
3 4
D1+ RESERVED D1- ADD1
Figure 17. ADT7484A Typical Application Schematic
VCC
1 2
ADT7486A
VCC GND SST ADD0
10 9 8 7 6
SST
2N3904 NPN
3 4 5
D1+ RESERVED D1- D2+ ADD1 D2-
CPU THERMAL DIODE
Figure 18. ADT7486A Typical Application Schematic
ORDERING INFORMATION
Device Order Number* ADT7484AARZ-REEL ADT7484AARZ-RL7 ADT7484AARMZ-RL ADT7484AARMZ-R7 ADT7486AARMZ-RL ADT7486AARMZ-R7 Branding - - T20 T20 T22 T22 Package Option R-8 R-8 RM-8 RM-8 RM-10 RM-10 Package Type SOIC-8 NB SOIC-8 NB 8-Lead MSOP 8-Lead MSOP 10-Lead MSOP 10-Lead MSOP Shipping 2500 Tape & Reel 1000 Tape & Reel 3000 Tape & Reel 1000 Tape & Reel 3000 Tape & Reel 1000 Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *These are Pb-Free packages.
http://onsemi.com
11
ADT7484A/ADT7486A
PACKAGE DIMENSIONS
SOIC-8 NB CASE 751-07 ISSUE AJ
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. DIM A B C D G H J K M N S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0_ 8_ 0.010 0.020 0.228 0.244
-X-
A
8 5
B
1
S
4
0.25 (0.010)
M
Y
M
-Y- G
K
C -Z- H D 0.25 (0.010)
M SEATING PLANE
N
X 45 _
0.10 (0.004)
M
J
ZY
S
X
S
SOLDERING FOOTPRINT*
1.52 0.060
7.0 0.275
4.0 0.155
0.6 0.024
1.270 0.050
SCALE 6:1 mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
12
ADT7484A/ADT7486A
PACKAGE DIMENSIONS
MSOP8 CASE 846AB-01 ISSUE O
D
HE
E
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. 846A-01 OBSOLETE, NEW STANDARD 846A-02. MILLIMETERS NOM MAX -- 1.10 0.08 0.15 0.33 0.40 0.18 0.23 3.00 3.10 3.00 3.10 0.65 BSC 0.40 0.55 0.70 4.75 4.90 5.05 MIN -- 0.05 0.25 0.13 2.90 2.90 INCHES NOM -- 0.003 0.013 0.007 0.118 0.118 0.026 BSC 0.021 0.016 0.187 0.193 MIN -- 0.002 0.010 0.005 0.114 0.114
PIN 1 ID
e
b 8 PL 0.08 (0.003)
M
TB
S
A
S
-T- PLANE 0.038 (0.0015) A1
SEATING
A c L
DIM A A1 b c D E e L HE
MAX 0.043 0.006 0.016 0.009 0.122 0.122 0.028 0.199
SOLDERING FOOTPRINT*
8X
1.04 0.041
0.38 0.015
8X
3.20 0.126
4.24 0.167
5.28 0.208
6X
0.65 0.0256
SCALE 8:1
mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
13
ADT7484A/ADT7486A
PACKAGE DIMENSIONS
MSOP10 CASE 846AC-01 ISSUE O
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION "A" DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION "B" DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. 846B-01 OBSOLETE. NEW STANDARD 846B-02 S DIM A B C D G H J K L MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.95 1.10 0.20 0.30 0.50 BSC 0.05 0.15 0.10 0.21 4.75 5.05 0.40 0.70 INCHES MIN MAX 0.114 0.122 0.114 0.122 0.037 0.043 0.008 0.012 0.020 BSC 0.002 0.006 0.004 0.008 0.187 0.199 0.016 0.028
-A-
K
-B-
PIN 1 ID
G
D 8 PL 0.08 (0.003)
M
TB
S
A
0.038 (0.0015) -T- SEATING
PLANE
C H J L
SOLDERING FOOTPRINT*
10X
1.04 0.041
0.32 0.0126
10X
3.20 0.126
4.24 0.167
5.28 0.208
8X
0.50 0.0196
SCALE 8:1
mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative
http://onsemi.com
14
ADT7484A-86A/D

▲Up To Search▲

Price & Availability of ADT7484A

	To Download ADT7484A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .